How To Tie Down Bike In Truck Bed

The motorcycle sometimes needs to be carried in the truck due to dirt, a damaged bike, or some other reason. You must fasten it when picking up a damaged bike, or a dirt bike from a truck. But we are unsure about How To Tie Down Bike In Truck Bed. In order to secure the bike for carrying, here is the step-by-step way to put the bike in the truck bed.

You will need the right equipment, including a solid pair of straps like ratchet straps or cam straps. Next, set the parking brake on the truck, engage the manual transmission if it has one, and remove the tailgate before loading your bike.

A motorcycle must be securely fastened to the vehicle during transport. The vehicle’s frame is compressed during this form of transportation, which helps in keeping the straps tightened. However, allow us to explain our suggested loading strategies for transporting a bike.

The Basics of Transporting a Bike

When transporting the bike, safety is a concern. The ideal equipment for that task is a set of tie-downs for motorcycles that are fastened to the bike and used to draw it down and forward in the tow truck.

Ratchet and cam straps are the two types of tie-down straps. In order to keep the strap in place, cam buckles use friction caused by the strap as it moves through a spring-loaded, cam-shaped clasp. Cargo tie-down straps, called ratchet straps, are constructed of polyester webbing. It goes through a buckle that enables you to change how tight or flexible the strap goes.

Your bike’s suspension might collapse if the vehicle transporting it runs into a hole or other disruption on the roadway. So, properly straps the bike down with the truck.

Best Way To Tie Down Bicycle In Truck Bed

bikes in truck bed

Get the Equipment

Since the equipment is fairly expensive, you must move the bike with care. Please use the right equipment to carry the motorcycle. Because fixing your damaged bike’s bodywork and paint won’t fix everything. You’ll need the cost of repairs.

The first and most crucial tool is a vehicle that is suitable for low, sturdy, and holding motorcycles securely. Due to its larger bed and lower load height, a 2WD long-bed pickup is much simpler to work with than a boosted 4WD step-side truck.

Arched ramps are fantastic because they reduce the negative impact of a break-over angle. A ramp with an arched top divides a single, rather right angle into several smaller ones.

Another “bare minimum” piece of equipment that aids in maintaining the wheel’s straightness is a chock. It is constructed with discarded 2x4s. Ratchet or cam-buckle straps are typically used.

Sportbike riders, pick a set of Canyon Dancers. Alternatively, you may use online service platforms to hire specialized bike transportation facilities.

Remove the Seat

Use a release tool to quickly remove the seat within 10 seconds if the bike looks better without one. Keep in mind that the back tire will contact the floor and the front edge of the bed when the seat is uninstalled.

Some bikes should have seats because, when turned over backward, the seat tube will touch the tire on those motorcycles. Many individuals choose to tie themselves down to a seat rather than remove it. We will talk about this soon. Keep reading!

You may search for: How to install Harley passenger seat?

Position The bike

Make sure the bike is positioned symmetrically. Your trailer or vehicle bed should first have a chock fastened to it. It should be centered and positioned at the foot of the bed. After that, tighten it.

Securing the Wheel

Hold the bike straight and avoid leaning to one side. Every time, put the front wheel of a motorcycle in first. Place the front wheel of the bike in the chock and roll it to the back of the trailer.

Extra straps will be used to secure the front tires to stop them from free-wheeling. Additionally, you must align your ramp with the wheel chock in the truck bed and then press your bike directly into the chock when you load it onto the truck bed or trailer.

Related Article: how many brake pads per wheel?

Flat Ground For Parking

Pick a level surface to park your vehicle on to transport the bike. It’s fantastic to use a loading dock at your property because it will avoid the need to lift your bike into the truck bed. The ideal method for transport is a loading ramp.

Get The Tie-Downs Setup – 7 Easy Steps

how to tie down a motorcycle
  • Most bikes can be secured with two ratchet tie-downs in the front and two on either side. But for additional security, six ratchet tie-downs, four in front and two at the back, will provide the most protection when it’s Boss Hoss.
  • If you’re using extension straps, place them around the bottom triple tree, the most secure place to set up.
  • Additionally, ratchet down or tighten the S-hooks on the straps by grabbing the loose end and dragging it against the bike’s frame. The tie-downs need to sag down a few inches in front of your attachment point.
  • Ratchet straps should be used to secure it to the anchor points in the corner of your truck bed. As a result, the front wheel has a secure anchor. Also, wheel chocks can be secured using straps or bolts.
  • Alternatively, tuck the front tire of the bike into the front corner of the bed. The metal hooks on the strap should be reattached to the metal tie-down points in the truck bed’s corner, bed surface, or bed rails.
  • Once you notice the suspension beginning to gradually compress, tighten the strap. Repeat these steps on the other side of the bike.

Compress The Suspension

The motorcycle’s suspension is compressed when it is strapped down, which helps keep the straps tight but shouldn’t be done for an extended period of time. Tighten the strap more when you notice a slight pressure on the suspension. In this case, ratchet straps work best!

By placing a substantial block between the front tire and fender, you may avoid overcompressing the fork when securing the triple clamp. Anyway. Just be careful not to overtighten the straps.

Place Your Bike in The Middle

Another critical step is to put the bike in the vehicle as best you can. Some individuals turn their bicycles or bikes on their backs and lean them up against the front of the truck bed but it’s better if you strap it right and keep it in the middle.

Strap Back & Front

The strap should be wrapped around the bike’s seat tube after being fastened to the D-Ring on the driver’s side. Next, connect the second hook of the strap after that, then tighten it against the bed’s front wall. Done with the back part!

Then fasten the front using the rear D-Rings. Use additional straps when on the roadway for more security.

Remove The Tailgate

You may have a 2006 Dodge RAM 1500 Quad Cab, for instance, and you want to carry your bike there. This is to let you know that a simple tool called a tailgate pad makes it possible to “throw” a bike over a truck’s tailgate without damaging the bike’s paint or the truck’s body. Some individuals use moving blankets over the tailgate.

A vehicle with a six-foot bed may have been delivered with just 16″ of the bed remaining before the tailgate. To avoid damage, you might need to remove the tailgate if your bike weighs 400 pounds or more.

The owner’s manual will show you how to remove the tailgate if your bike weighs more than the weight restriction of the tailgate. The tailgate and ramps must be locked, and keep in mind that your front tire will be in the front-left corner and your rear tire will be in the back-right.

Related tire: how much are Motorcycle tires?

Newton’s Third Law of Motion

As per Newton’s Third Law, “for every action (force) in nature, there is an equal and opposite reaction” when you transfer the bike into the truck bed. In order to prevent forces from braking, accelerating, side winds, or turning, you must secure the bike from all angles.

The Shake Test

Less than an inch of displacement can have a significant impact on your bike. So, double-test each strap for proper tightness after your initial tightening. To make sure it is firmly attached, shake it.

Best Tie-Down Points On Large bike

how to transport bike in truck bed
  • D-rings are often pre-installed on models to be used as cable or chain lock tie-down points. You can also use side clamp racks to hold bikes and secure a variety of large things in your truck bed.
  • The straps should create a 45-degree angle between the bike and the ground.
  • Using a soft loop around the triple tree and tying the loop off with two ratchet straps is advised by the Yamaha Venture and Honda Gold Wing owner forums.
  • It’s a terrific idea to duplicate the four-strap tie-down and attach tie-downs to the front of engines on motorcycles like Harleys.

Related Article: How much does a Harley Sportster weight?

What To Avoid While You Tie Down The Bike With Truck

Tie Down a Dirt Bike in a Truck Bed needs to avoid a few things. Let’s have a look at this.

  • When securing the bike, never ever overtighten the straps. If the seal is already broken, that could be enough to destroy it. As a result, some flexibility is needed.
  • The majority of people probably 87.93% load the bike directly into the vehicle. However, you shouldn’t place your bike directly into the bed of the truck, with the front wheel against the bed behind the cab.
  • Certain handlebars have rubber mounts, and as they compress, the tie-downs might slip.
  • Rear bag guards should not be used as points of connection since they will be yanked off.
  • With a LINE-X vehicle bed liner, you should protect your vehicle.

Also Read: How much does a 250 dirt bike weigh?

FAQ

1. How do you tie down a motorcycle in a U-Haul truck?

Ratched straps work well for securing the bike with a truck. To secure the paint, tie up any loose ends and use the sidewalls and tie points of the vehicle.

2. How do you strap a mountain bike in a truck bed?

It takes only a few seconds to remove the seat, flip it over with the back wheel confronting the truck cabin, attach ratcheted straps to the anchor point, and tighten them appropriately.

3. How do you transport a bike without a rack?

Without a rack, place the bike in the backseat of your car, secure it to the roof, and transport it using a travel bike case. Sometimes you can remove the parts, like the wheels or chains, of your bike that you need to carry and then readjust everything.

4. How do you tie down a motorcycle without a wheel chock?

Use soft straps to secure the bike, then wrap each one through a ratchet strap, slightly compress the shocks, and secure the ends to the sides of the trailer or the supports in the bed of your truck.

Concluding Section

So, that’s all about carrying the bike in the truck process. We have shared every single detail regarding How To Tie Down Bike In Truck Bed properly. Therefore, make sure you get the proper tools, remove the seat and tailgate, position the bike, secure the wheel, and tie it down with straps to carry it in your truck.

Anyway, follow our given instructions and if you find it difficult, feel free to leave your issues. We will provide you with a solution for transporting dirt bikes with a truck. 

Share on:

Hello, this is Adam Willam, the owner and author of the website- "motobikekit.com". I have been passionate about biking since I was a child and have always been fascinated by the mechanics of how bikes work. When I became old enough, I started my own business of repairing and customizing bikes. By doing this I have quickly gained a reputation for being the go-to guy for bike repairs and customizations and have been running my shop successfully for many years.

Leave a Comment